Відео

Excellent video! Thank you

Great vid guys. I am a bit of a novice, recently bought a Minn Kota to have as a spare engine on my river boat. Looking for some advice, if i use the Minn occasionally for a couple of hours, would i have to recharge the marine battery every time? In other words, would the battery not automatically recharge when i'm using my outboard petrol engine? Many thanks for any advice you can offer.

I cannot loosen the nut. Too tight. Now what.

Fantastic. Thanks!

Thanks for the help

quelle est la matière de la plaque blanche

I tried this works great I'm going to use coaxial cable ties and drill a few holesw so i don't need zip ties

has anyone thought about drilling some hole were the zip ties are and tap it us a zip tie that can be bolted

Probably one of the worst videos I have ever watched. 😢

Great production. Very thorough. Easy to understand.

I am replacing my veritable speed switch on my Minn Kota and the new switch wires are red white and black my old one has 2 black wires and a yellow/green wire not sure how to wire it to work Thanks

Great vid

So do I hold down the button after I select the correct type? The instructions didn’t say. Nor the video.

Mine will not stow after 1 month used. Garbage. Thanks Johnson

Thanks perfect video for anyone to install one ,Im installing mine today

Thank you!! Great video! Excellent job filming and explaining!

Interesting ...no running lights makes it easy

Thanks from Ukrainian

Are you able to keep the wires connected at all times when you are using the boat and also when charging?

i cant seem to get the trolling motor contols for the ulterra quest onto my solix 12

Do you put anti seize on the prop?

Should I keep the motor power cord long ? Or cut shorter.

Why would you put the pump into maintenance mode? This video is really confusing because I've learned how to put the raptor pump into maintenance mode but why do I need to move the raptors up and down manually?

Good video

It’s the quick release mount worth the price tag? In comparison to the standard mount that the unit comes with?

Why can't you use the foot control? Suppose your out on the lake and remote quits?

Do you have a part number for the brush spreader tool and where can I get one? Thx!

i would like to know how to find and use the recorded tracks on the phone app

Hi I have a Ulterra 36 Volt Minn Kota and want to replace the wires from the Minn Kota Removable Plug and Socket but there are no details where the wires are connected to Minn Kota unit as it was disconnected for a repair to the control unit due to water ingress but There are no clear points to connect new wires. Are the new wires needing 90 Degree female Spade connectors as I did not disconnect the wiring I don't want to get the Positive and Negative in the wrong way as other unit I have seen show both cables with female connectors on the new wires surely they should not be able to get cross connected ie negative onto positive terminal . Is the Right connector Positive? And is the Left terminal the Negative? As athe installer of my unit made up a female to male short extension which will cause higher resistance over time as the corrosion takes over due to the lack of water proofing in the electrical connector area. Pretty Bad Design for a unit that is sold for Salt Water Usage? With No adequate Sealing to keep any water away from the power supply connections corrosion and failures are going to occur on a regular basis. I have also had issues with the Shaft delaminating after Three months use, Had it Replaced then the control unit gets water ingress and shorts out the PC board. This is not a well designed unit Not Fit For Purpose for use in salt water or even in rain in my opinion

This motor has failed me 3 times now 😡😡😡😡

How will the PCL charger interact with a BMS that floats the voltage at 12.8v after reaching a full charge at ~13.5v? Will it read it as being low charge and reinitiatethe charging process if left plugged in? What voltage would initiate a charging cycle after completing a full charge in the lithium setting?

The new Quest motors are fantastic! However I recommend MinnKota supply a longer mounting bolt with there composite bracket. The provided bolts are too short for many applications and longer ones are hard to source. 👍🏻

Ted is tough!

During disassembly, I had a smaller lower unit seal paper bore fall out and I ca not find where it goes…. Any idea???

Wish it was that easy

How do you put it back

Does a heading sensor make a power drives spotlock more accurate? Or only add the jog feature?

How do you calibrate with micro remote ? It’s the only remote I have…

Great video! However you didn't mention the clearance needed from the gunnel to the motor shaft though. Needs to be at least a 1-3/8" gap

How far away can you be with the remote. Or what is the range?

That's a good trick to know. Solved my issue today and saved me time and money.

A flathead on the end of the shaft is the dumbest invention ever made. The nut will seize up and the flathead will strip🙄

Nice video, very detailed and good advice. One tip, cleaning up silicone off your hands and/or excess that squeezes out, such as in this case, use a paper towel and rubbing alcohol, comes right off - nice and clean job!

I bought a used Minn Kota 24/36 volt trolling motor. How do I know what type of control board is in it? If I took a pic and sent it in, would you be able to identify it? Thanks for your time.

Excellent Video, But At 16:19 I disagree, in the minn kota ulterra owners manual Minn kota recommends greasing the stow and deploy shaft with marine grease, I’ve been doing that and no issues, I strongly recommend greasing it for smooth stow and deploy,

If I want to put a foot pedal back on I guess it’s the same process in reverse? Anything I need to know about?

How much of that nose cone is solid? If I needed to trim off 1/2 to 5/8 of an inch is there enough material there to do that? Or is it pretty much hollow with the exception of the potting material?

How much of that nose cone is solid? If I needed to trim 1/2 to 5/8 of an inch off of the nose is that possible? Or is the nose hollow all the way to the end?

Les agradeciera mucho por s ayuda